Though the DJI Flip is a really new drone (as of this text’s writing), having been launched in January 2025, it has already obtained a number of firmware updates.
For these new to drones normally, firmware updates are crucial for drones. It’s because they oftentimes implement efficiency enhancements, add new options, and handle and repair bugs that in any other case hamper a wonderful flight expertise.
This text serves as a step-by-step information exhibiting find out how to replace the DJI FlySafe Databases and firmware on the DJI Flip and DJI RC 2 distant controller.
Updating the Flip’s Firmware
For individuals who have been flying drones for some time, staying with a drone’s unique launch firmware was a typical observe, a observe we likewise adopted.
This was primarily as a result of the firmware updates then would oftentimes break a function or trigger the drone to fly inconsistently. With newer drones, just like the Flip, updating the firmware is helpful.
As talked about, new options, tweaks, and fixes are added over time. These updates enhance the general consumer expertise.
DJI has been fairly dedicated to enhancing the flight traits of their new line of drones, recurrently.
To replace the firmware in your DJI Flip, you’ll want your:
- DJI Flip and put in battery
- DJI distant controller (on this occasion the DJI RC 2)
Moreover, we advise that any time you run a firmware replace in your drone, have the Flip batteries and distant controller totally charged earlier than working firmware updates.
The steps to replace the firmware in your Flip are as follows:
STEP 1: Earlier than turning on the DJI Flip, take away the gimbal and silicone digicam covers. This may be certain that when the Flip is turned on, the gimbal’s motion is not going to be impeded and trigger errors.
STEP 2: After booting up your DJI RC 2, be sure to are related to a WiFi community. To test this, go into your settings display screen by double-sliding down the notification shade. In case your WiFi will not be enabled, faucet the WiFi icon and await a connection.
If you’re connecting to WiFi for the primary time, press and maintain the WiFi icon. This may convey you into the WiFi settings. Right here you possibly can connect with your most well-liked community.
STEP 3: Activate the Flip. Press, then press and maintain the ability button.
Be aware: When you have not modified the “energy on when unfolded choices” within the DJI Fly app, ignore this step.
STEP 4: From inside the Digital camera View display screen, press the again button, which can take you to the Flip house display screen.
Right here you will note that there’s a firmware replace out there. Select Replace.
In the course of the replace course of, the lights on the Flip will flash. The DJI RC 2 might also reboot itself. You can be alerted when the replace is full.
Be aware: Oftentimes, the Flip could not restart itself after the Replace is full. You might have to manually energy it on afterward to start flying.
Manually Checking for Firmware Updates
When you have not been prompted mechanically that there’s a new firmware out there, you possibly can manually test for updates, by doing the next:
With the DJI RC 2 turned on and related to your WiFi community, whereas on the DJI Fly house display screen, merely go to Profile > Settings > Firmware Replace > Test for Firmware Updates.
After the DJI RC 2 checks for the replace, if there’s none, you’ll obtain a message saying “Your firmware is updated”.
If there’s a new firmware replace, you’ll be alerted and can have the choice to run the replace.
Updating the FlySafe Database
Firstly, what’s FlySafe information?
Immediately from DJI: “FlySafe information is designed to assist pilots higher perceive flight dangers, make knowledgeable choices, and mitigate security dangers by figuring out restricted and prohibited geographic areas. DJI offers computerized updates to such information primarily based on native rules and inside threat evaluation. The completeness, accuracy, and effectiveness of the information will not be assured, and such information must be used for reference solely.”
Like with firmware updates, updating the FlySafe Database is an easy course of.
To replace the Flip’s FlySafe Databases:
STEP 1: Earlier than turning on the DJI Flip, take away the gimbal and silicone digicam covers. This may be certain that when the Flip is turned on, the gimbal’s motion is not going to be impeded and trigger errors.
STEP 2: After booting up your DJI RC 2, be sure to are related to a WiFi community. To test this, go into your settings display screen by double-sliding down the notification shade. In case your WiFi will not be enabled, faucet the WiFi icon and await a connection.
If you’re connecting to WiFi for the primary time, press and maintain the WiFi icon. This may convey you into the WiFi settings. Right here you possibly can connect with your most well-liked community.
STEP 3: Activate the Flip. Press, then press and maintain the ability button.
Be aware: When you have not modified the “energy on when unfolded choices” within the DJI Fly app, ignore this step.
STEP 4: From inside the Digital camera View display screen, press the again button, which can take you to the Flip house display screen.
STEP 5: If there’s a FlySafe Database Replace out there, it is going to present on the DJI Fly homescreen.
Press Replace and the FlySafe Database will proceed to replace.
The method solely takes a minute or two and shouldn’t restart your DJI Flip.
